Adaptec 131U2 - AAA RAID Controller Manual de Instruções Página 51
- Página / 82
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5-1
è
▼ ▼ ▼ ▼
Installing the Software
Driver for Novell NetWare
In this Chapter
This chapter explains how to install the AAA-131U2/133U2 soft-
ware driver (
cda1000h.ham
) for Novell NetWare (NetWare 4.11, 4.2,
and 5.0). Before installing the driver, make sure you have completed
the following:
■
Installed the AAA-131U2/133U2 in your system
(See Chapter 2)
■
Created the first array using the
ARRAYCONFIG U2
utility, if
you plan to boot from an array. (See Chapter 3)
Once NetWare and the driver are installed, install Adaptec CI/O
Management Software from the server console (CI/O is required for
array management in order to provide the proper level of fault
tolerance and event notification). Refer to the
Adaptec CI/O Manage-
ment Software User’s Guide
for instructions on installing and using the
software.
➤
Installing the Array1000U2 Driver for Novell NetWare
5-2
➤
Netware Installation and Configuration Notes
5-8
- NSTALLATION 1
- 691 South Milpitas Boulevard 2
- Milpitas, CA 95035 2
- Printed in Singapore 2
- Adaptec, Inc 2
- AAA-130U2 Series 3
- Copyright 4
- Trademarks 4
- Disclaimer 4
- Canadian Compliance Statement 5
- Contents 7
- External Cables D-2 9
- Internal Ribbon Cables D-2 9
- Introduction 11
- System Requirements 12
- Installation Overview 13
- Installing the Hardware 15
- Installing DIMM Memory 17
- AAA-131U2 Card Installed in 18
- PCI Expansion Slot 18
- Setting Up SCSI Devices 20
- Terminate the Ends 21
- All SCSI Devices 22
- Cable Lengths 22
- Connecting SCSI Devices 23
- AAA-131U2/133U2 24
- Te r m i n at o r 24
- Ultra2 SCSI Devices 26
- Terminator 26
- AAA-131U2 RAID Card 28
- AAA-133U2 RAID Card 28
- High-density 68-pin External 30
- Ultra2 SCSI Cable 30
- Active Terminator 32
- Array Enclosure 32
- Creating an Array With the 35
- ARRAYCONFIG U2 Utility 35
- Creating an Array 36
- Caution: 40
- Making the Array Bootable 42
- Installing the Software 45
- Driver for Windows NT 45
- If Windows NT Setup Hangs 49
- Windows NT Disk Administrator 49
- Driver for Novell NetWare 51
- NetWare 4.11 and 4.2 52
- NetWare 5.0 55
- Larger Than 4 GByte Arrays 58
- Unloading cda1000h.ham 58
- Driver for SCO UnixWare 59
- Using SCSISelect and Disk 63
- Utilities 63
- Default Settings 64
- Starting the SCSI 65
- Utility 65
- Using the SCSI Disk Utilities 66
- Settings 67
- Additional Options 68
- Troubleshooting 69
- Windows NT Troubleshooting 70
- “Partition Size Too Large” 71
- Using a CD-ROM Drive 73
- ■ Sample command lines for 74
- ■ Sample command line for 74
- Obtaining SCSI Cables 77
- External Cables 78
- Internal Ribbon Cables 78
- ▼ ▼ ▼ ▼ 79
Ricoh Cámaras Bridge manuales de usuario
Empezando en F
Comentários a estes Manuais