Adaptec 2910C - AHA Storage Controller Fast SCSI 10 MBps Manual do Utilizador Página 165
- Página / 190
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
6-13
SCO UNIX Installation
Troubleshooting
Problems and Solutions
In SCO OpenServer 5, my system hangs after I have installed the driver and rebooted
the system.
If you are installing OpenServer 5, version 5.0.0, you may have to
install the SCO OpenServer 5 keyboard patch (available from the
SCO Web site or BBS) at the same time you install the
alad325
driver. To install the keyboard patch at the same time you install
SCO OpenServer 5 and the
alad325
driver, type the following
instead of the ahslink command described above:
defbootstr ahslink = “kbp alad325”
Follow the onscreen instructions to insert the SCO keyboard patch
diskette (kbp) and the 7800 Family Manager Set diskette for SCO
UNIX when instructed.
I have problems using my SCSI devices.
During bootup, check to see if the BIOS messages for your primary
7800 Family host adapter lists all installed SCSI devices. If some or
all devices do not appear, check the following (also check your host
adapter’s User’s Guide for additional troubleshooting information):
■
Are all SCSI devices powered?
■
Are all SCSI bus cables and power cables properly connected?
■
Do the host adapter and all devices on the SCSI bus have
unique SCSI IDs?
■
Are all devices on the SCSI bus terminated properly?
■
Do you have an older SCSI peripheral installed? Some older
SCSI peripherals, especially CD-ROM drives, do not properly
respond to synchronous negotiation. As a result, these
peripherals may lock or reset the SCSI bus. To solve this
problem, turn off synchronous negotiation for this device ID
through the SCSISelect utility for the host adapter. See the host
adapter’s User’s Guide.
- P2B-D / P2B-DS 1
- USER’S MANUAL 1
- USER'S NOTICE 2
- ASUS CONTACT INFORMATION 3
- CONTENTS 4
- FCC & DOC COMPLIANCE 6
- I. INTRODUCTION 7
- II. FEATURES 8
- Board Layout 10
- III. INSTALLATION 10
- III. INSTALLATION 11
- Jumper Settings 13
- P2B-D/DS CPU Settings 14
- (Default) 15
- JP18 JP18 15
- SDRAM DIMM (8 chips, Non-ECC) 17
- NOTE: Insert the 20
- P2B-D/DS IDE Activity LED 29
- Chassis Signal 31
- Ultra2 Devices 33
- Single-Ended Devices 33
- P2B-D/DS SB-Link™ Connector 34
- IV. BIOS SOFTWARE 36
- IV. BIOS SOFTWARE 39
- V. SUPPORT SOFTWARE 58
- VI. DESKTOP MANAGEMENT 59
- VII. ASUS LAN Card 63
- VIII. ADAPTEC SCSI SELECT 65
- IX. ADAPTEC EZ-SCSI 67
- Adaptec 7800 Family 75
- Manager Set 75
- Canadian Compliance Statement 77
- Contents 79
- 4 Novell NetWare Installation 80
- 5 IBM OS/2 Installation 80
- 6 SCO UNIX Installation 81
- 7 SCO UnixWare Installation 81
- Troubleshooting 7-11 82
- Problems and Solutions 7-11 82
- Error Messages 7-11 82
- Introduction 83
- Device Drivers 84
- Requirements 87
- Microsoft Windows NT 89
- Updating Windows NT 4.0 95
- Caution: 96
- \Parameters\Device 97
- Removing a Host Adapter 100
- Adaptec 7800 Family Manager 102
- Swapping a Host Adapter 103
- Troubleshooting 104
- Error Codes 105
- [xxxxxd4] 108
- [xxxxx0d6] 108
- Microsoft Windows 95 109
- Installation 109
- Already Installed 110
- Novell NetWare Installation 117
- NetWare v3.1x 118
- NetWare v4.0 or v4.1x 119
- Installed 120
- Bit Mask Options 128
- Sample Load Commands 128
- Using Removable Media 129
- Mount Status 130
- Lock Status 130
- Verify ( 130
- driver only) 130
- Using the NetWare Tape Backup 131
- Using a CD-ROM with NetWare 132
- Optimizing Performance 133
- IBM OS/2 Installation 137
- Using Command Line Options 144
- Adapter ID 145
- Unit Parameters 145
- Command Line Examples 147
- SCO UNIX Installation 153
- SCO OpenServer 3.0 154
- Installing SCO OpenServer 5 156
- Perform a System Backup 158
- Use the Install Package 159
- Modify the mscsi File 160
- Rebuild the UNIX Kernel 161
- Boot the New Kernel 162
- Using Multiple Host Adapters 162
- Changing the Boot Disk 162
- Examples 164
- Error Messages 169
- /etc/conf/pack.d/alad/space.c 170
- SCO UnixWare Installation 171
- UnixWare 172
- Back Up the Computer 174
- Load the Package 174
- Modify the New System File 176
- Using Tunable Parameters 178
- Removing the Driver 179
- ▼ ▼ ▼ ▼ 187
Manuais e produtos relacionados com Placas-mãe Adaptec 2910C - AHA Storage Controller Fast SCSI 10 MBps
Placas-mãe Adaptec AHA-3940 Guia do Utilizador
(102 páginas)
(102 páginas)
Placas-mãe Adaptec 3940AUW Manual do Utilizador
(128 páginas)
(128 páginas)
Placas-mãe Adaptec AHA-2740W Guia de Instalação
(0 páginas)
(0 páginas)
Placas-mãe Adaptec 1045 Guia do Utilizador
(69 páginas)
(69 páginas)
Placas-mãe Adaptec AHA-2742 Guia do Utilizador
(118 páginas)
(118 páginas)
Placas-mãe Adaptec AHA-1744 Guia de Instalação
(191 páginas)
(191 páginas)
Placas-mãe Adaptec AVA-2825 Guia do Utilizador
(110 páginas)
(110 páginas)
Placas-mãe Adaptec AHA-1540CP Guia de Instalação
(14 páginas)
(14 páginas)
Placas-mãe Adaptec AHA-1540B Guia de Instalação
(14 páginas)
(14 páginas)
Placas-mãe Adaptec AHA-2742 Guia de Instalação
(25 páginas)
(25 páginas)
Placas-mãe Adaptec AHA-1540B Guia de Instalação
(5 páginas)
(5 páginas)
Placas-mãe Adaptec AHA-3940 Guia do Utilizador
(102 páginas)
(102 páginas)
Rail King 2-8-0 Steam Freight Set manuals
Owner’s manuals and user’s guides for Toys & accessories Rail King 2-8-0 Steam Freight Set.
We providing 1 pdf manuals Rail King 2-8-0 Steam Freight Set for download free by document types: Operator's Manual
Comentários a estes Manuais