Adaptec ICP5045BL Guia do Utilizador Página 65
- Página / 135
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 10: Solving Problems ● 65
Failed Disk Drive Protected by a Hot Spare
When an array is protected by a hot spare, if a disk drive in that array fails the hot spare is
automatically incorporated into the array and takes over for the failed drive.
To recover from the failure:
1 Remove and replace the failed disk drive (following manufacturer’s instructions).
2 If copyback is not enabled—In ICP Storage Manager, remove the ‘hot spare’ designation
from the original hot spare (the disk drive that was built into the array). Then, designate a
new hot spare to protect the arrays on that controller.
If copyback is enabled—Data is automatically moved back to its original location once the
controller detects that the failed drive has been replaced. No action is required.
Failed Disk Drive Not Protected by a Hot Spare
When a array is not protected by a hot spare, if a disk drive in that array fails, remove and
replace the failed disk drive. The controller detects the new disk drive and begins to rebuild the
array.
If the controller fails to rebuild the array, check that the cables, disk drives, and controllers are
properly installed and connected. Then, if necessary, use ICP Storage Manager to rebuild the
array. For instructions, refer to the ICP Storage Manager User’s Guide or online Help.
Failure in Multiple Arrays Simultaneously
If there’s a disk drive failure in more than one array at the same time (one failure per array),
and the arrays have hot spares protecting them, the controller rebuilds the arrays with these
limitations:
● A hot spare must be of equal or greater size than the failed disk drive it’s replacing.
● Failed disk drives are replaced with hot spares in the order in which they failed. (The array
that includes the disk drive that failed first is rebuilt first, assuming an appropriate hot
spare is available—see bullet above.)
If there are more disk drive failures than hot spares, see Failed Disk Drive Not Protected by a Hot
Spare.
If copyback is enabled, data is moved back to its original location once the controller detects
that the failed drive has been replaced.
Disk Drive Failure in a RAID 0 Array
Because RAID 0 volumes do not include redundancy, if a disk drive fails in a RAID 0 array, the
data can’t be recovered.
Correct the cause of the failure or replace the failed disk drives. Then, restore your data (if
available).
- SAS, SATA, and SCSI 1
- RAID Controllers 1
- Installation and 1
- User’s Guide 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- ICP vortex Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- Using the ICP Flash Utility 10
- Safety Information 10
- Technical Specifications 10
- About This Guide 11
- How to Find More Information 12
- Kit Contents and System 13
- Requirements 13
- Kit Contents 14
- About Your RAID Controller 15
- Array-level Features 16
- RAID Controller Battery Model 17
- About the ICP5805BL 18
- About the ICP5045BL 19
- About the ICP5085BL 20
- About the ICP5125BR 21
- About the ICP5165BR 22
- About the ICP9085LI 23
- About the ICP5085BR 24
- About the ICP9047MA 25
- About the ICP9087MA 26
- About the ICP9014RO 27
- About the ICP9024RO 28
- Getting Started 29
- Choosing a RAID Level 30
- Selecting Disk Drives 31
- Selecting Cables 32
- SATA Cables 33
- Installation Options 34
- Basic Installation Steps 34
- In this chapter 36
- Installing the Controller 37
- Connecting External Devices 41
- Creating a Bootable Array 42
- Setting the Boot Controller 43
- Creating an Array 43
- Making Your Array Bootable 46
- Installing the Driver and an 47
- Operating System 47
- Creating a Driver Disk 48
- Installing with Windows 49
- Installing with Red Hat Linux 49
- Installing with SUSE Linux 50
- Installing with NetWare 50
- Installing with OpenServer 51
- Installing with Solaris 51
- Installing with UnixWare 52
- Installing with VMware 52
- Installing with FreeBSD 53
- Installing on Windows 56
- Installing on NetWare 56
- Installing on OpenServer 57
- Installing on Solaris 57
- Installing on UnixWare 58
- Installing on VMware 58
- Installing on FreeBSD 59
- Managing Your Storage Space 60
- About ICP Storage Manager 61
- About the ICP Flash Utility 62
- Which Utility Should I Use? 62
- Solving Problems 63
- Troubleshooting Checklist 64
- Silencing the Alarm 64
- Resetting the Controller 66
- In this appendix 67
- ) Web site at www.scsita.org 67
- What is SAS? 68
- What’s a Phy? 69
- What’s a SAS Port? 70
- What’s a SAS Address? 70
- What’s a SAS Connector? 70
- What do SAS Cables Look Like? 70
- Direct-attach Connections 71
- Backplane Connections 71
- SAS Expander Connections 72
- Understanding RAID 74
- Understanding Drive Segments 75
- Non-redundant Arrays (RAID 0) 75
- RAID 1 Arrays 76
- RAID 1 Enhanced Arrays 76
- RAID 10 Arrays 77
- RAID 5 Arrays 78
- RAID 5EE Arrays 79
- RAID 50 Arrays 80
- RAID 6 Arrays 81
- RAID 60 Arrays 81
- Selecting the Best RAID Level 82
- Creating a New Array 84
- Managing Existing Arrays 85
- Initializing Disk Drives 85
- Rescanning Disk Drives 85
- Secure Erasing Disk Drives 86
- Opening a -Select Utility 86
- Applying Changes and Exiting 86
- General Controller Settings 87
- Option Description 88
- Locating Disk Drives 90
- Identifying Disk Drives 90
- Viewing the Event Log 91
- Running the ACU Using Scripts 94
- About Record Mode 95
- Required 96
- ? Description 96
- HotspareDrives=0:0:0,0:1:0 97
- InitializeAll=Yes 97
- ACU exits with an error 98
- Keyword Description 99
- ACU Error Codes 100
- Sample Scripts 101
- System Requirements 104
- Before You Begin 104
- Running the Menu-based IFU 105
- Running the 106
- Connector Reference 110
- Pin Number Signal Description 111
- 22-55-2161 113
- Pin Number 113
- SFF-8087 Connector J5: 120
- SFF-8087 Connector J18: 120
- SFF-8087 Connector J14: 124
- 22-552101 125
- Environmental Specifications 129
- DC Power Requirements 129
- Current Requirements 129
- Index ● 131 131
- Index ● 132 132
- Index ● 133 133
- Index ● 134 134
- Konrad-Zuse-Str.9 135
- 74172 Neckarsulm 135
Manuais e produtos relacionados com Controladores periféricos Adaptec ICP5045BL
Craftsman 580.752270 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Myjki wysokociśnieniowe Craftsman 580.752270.
Dostarczamy 1 pdf podręczników Craftsman 580.752270 do pobrania za darmo według typów dokumentów: Dokumentacja
Craftsman 580.752270 Dokumentacja (48 strony)
Marka: Craftsman | Kategoria: High-pressure cleaners | Rozmiar: 3.80 MB |
Spis treści
Add Fuel
7
Low Pressure
10
MAINTENANCE
13
Carburetor
15
3,,_32_3_
22
ADVERTENCIA
29
PRECAUCION
30
PRODUCTO
39
Carburador
42
INVIERNO
43
Your Home
48
Our Home
48
Więcej produktów i instrukcji dla Myjki wysokociśnieniowe Craftsman
| Modele | Rodzaj dokumentu |
|---|---|
| 580.768050 |
Instrukcje Operacyjne
Craftsman 580.768050 Operating instructions,
26 strony
|
| 580.752120 |
Instrukcja Operatora
Craftsman 580.752120 Operator`s manual,
60 strony
|
| 580.768020 |
Instrukcje Operacyjne
Craftsman 580.768020 Operating instructions,
26 strony
|
| 2,7 MAX GPM |
Instrukcje Operacyjne
Craftsman 2,7 MAX GPM Operating instructions,
56 strony
|
| 580.752340 |
Instrukcja Operatora
Craftsman 580.752340 Operator`s manual,
56 strony
|
| 580.767202 |
Instrukcja Właściciela
Craftsman 580.767202 Owner`s manual,
44 strony
|
| 580.752340 |
Instrukcja Operatora
Craftsman 580.752340 Operator`s manual,
56 strony
|
| 580.752910 |
Instrukcje Operacyjne
Craftsman 580.752910 Operating instructions,
60 strony
|
| HIGH PRESSURE WASHER 580.76225 |
Instrukcja Właściciela
Craftsman HIGH PRESSURE WASHER 580.76225 Owner`s manual,
26 strony
|
| 580 |
Instrukcje Operacyjne
Craftsman 580 Operating instructions,
28 strony
|
| 580.752360 |
Instrukcje Operacyjne
Craftsman 580.752360 Operating instructions,
60 strony
|
| D25852 |
Instrukcja Właściciela
Craftsman D25852 Owner`s manual,
28 strony
|
| 919.670280 |
Instrukcja Właściciela
Craftsman 919.670280 Owner`s manual,
28 strony
|
| 919.672240 |
Instrukcja Właściciela
Craftsman 919.672240 Owner`s manual,
44 strony
|
| 919.769010 |
Instrukcja Właściciela
Craftsman 919.769010 Owner`s manual,
52 strony
|
| D20590 |
Instrukcja Użytkownika
Hometown Sears. Shop Locally. Georgetown man,
1 strony
|
| 919.672190 |
Instrukcja Właściciela
Craftsman 919.672190 Owner`s manual,
80 strony
|
| 919.769063 |
Instrukcja Właściciela
Craftsman 919.769063 Owner`s manual,
40 strony
|
| 4.0 GPM Honda Powered Pressure Washer |
Instrukcja Właściciela
Craftsman 4.0 GPM Honda Powered Pressure Washer Owner`s manual [en] [es] [fr] ,
20 strony
|
| 580.767451 |
Instrukcja Właściciela
Craftsman 580.767451 Owner`s manual [en] ,
48 strony
|
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais