Adaptec AHA-2930CU Guia de Instalação

DiagnosticPRO™ DiagnosticPRO™ plus VXR-16 DosimetryPRO™ VXR-16™ Installation Guide

2 VIDAR Part Number 13022-006 Rev A October, 2003 © Copyright 2003 by VIDAR Systems Corporation. All rights reserved. Printed in the USA. No part

3 Contents Unpacking...5 Look for damage...

4 Scanning multiple films...49 Cleaning the Auto-Feed Roller ...

5 VIDAR Film Digitizer Installation Guide Unpacking Look for damage Before unpacking the film digitizer, examine the shipping carton for damage.

6 Unpacking VIDAR Film Digitizer Installation Guide Repacking the film digitizer IMPORTANT: When shipping the film digitizer, you must use the ori

Unpacking 7 VIDAR Film Digitizer Installation Guide Identify the components Unpack the carton and identify each of these components: 9 Item Unpa

8 Unpacking VIDAR Film Digitizer Installation Guide If anything is missing... Immediately contact your VIDAR supplier. Activate your product warra

9 VIDAR Film Digitizer Installation Guide Setting up Install the Multi-Film Feeder 1. Place the digitizer on a solid flat surface (such as a tab

10 Setting up VIDAR Film Digitizer Installation Guide c. On the back of the feeder, tighten both thumbscrews to secure the feeder to the digitizer.

Setting up 11 VIDAR Film Digitizer Installation Guide If necessary, set the digitizer’s SCSI ID A computer equipped with a SCSI bus can communicat

12 Setting up VIDAR Film Digitizer Installation Guide Terminate the SCSI bus The film digitizer has two SCSI port connectors, enabling it to be place

Setting up 13 VIDAR Film Digitizer Installation Guide Connect the SCSI cable For best performance, use the shielded SCSI cable available from VIDA

14 Setting up VIDAR Film Digitizer Installation Guide Connect the power cord 1. Connect the power cord to the digitizer’s Power Entry Module (PEM),

15 VIDAR Film Digitizer Installation Guide Installing SCSI hardware A SCSI controller (host adapter) is required to enable the VIDAR film digitize

16 Installing SCSI hardware VIDAR Film Digitizer Installation Guide Warning Before you begin the installation procedure, turn off all power to the c

Installing SCSI hardware 17 VIDAR Film Digitizer Installation Guide Install the SCSI card. a. Turn off power to the computer and disconnect the c

18 Installing SCSI hardware VIDAR Film Digitizer Installation Guide f. Insert the SCSI Card into the PCI expansion slot. Press down firmly until th

19 VIDAR Film Digitizer Installation Guide Installing device drivers So far, you have installed the SCSI hardware in your computer and assembled t

20 Installing device drivers VIDAR Film Digitizer Installation Guide 1. Turn on the digitizer a. Ensure the PC is turned off. Note: Always apply p

Installing device drivers 21 VIDAR Film Digitizer Installation Guide 2. Use the SCSI utility to configure the SCSI BIOS In most cases, the digitiz

Warranty information for VIDAR film digitizers Instructions: 1. Cut along dotted line at left. 2. Fill in. 3. Make a copy for your records. 4. E-ma

22 Installing device drivers VIDAR Film Digitizer Installation Guide d. Under Additional Options, select SCSI Device Configuration (see below). Press

Installing device drivers 23 VIDAR Film Digitizer Installation Guide f. Select Advanced Configuration Options (see below) and press <Enter>.

24 Installing device drivers VIDAR Film Digitizer Installation Guide 3. Install the scanning application Follow the instructions provded with the sca

Installing device drivers 25 VIDAR Film Digitizer Installation Guide VIDAR Drivers and Toolkit Installation CD VIDAR Drivers and Toolki

26 Installing device drivers VIDAR Film Digitizer Installation Guide VIDAR device driver summary Operating system Device driver EZ-SCSI Software Upd

Installing device drivers 27 VIDAR Film Digitizer Installation Guide Computers with Windows 2000 and Windows XP Note:  On Windows 2000 computers

28 Installing device drivers VIDAR Film Digitizer Installation Guide 4. When you are prompted to restart the PC: a. Close all open applications and

Installing device drivers 29 VIDAR Film Digitizer Installation Guide 7. In the Install Hardware Device Drivers page, activate Search for a suitable

30 Installing device drivers VIDAR Film Digitizer Installation Guide 9. When the Driver Files Search Results page confirms that the correct driver—vid

Installing device drivers 31 VIDAR Film Digitizer Installation Guide 11. In the Completing the Found New Hardware Wizard page, click Finish. 12

Product information What product are you registering? (Select only one)  DiagnosticPRO  DiagnosticPRO plus  VXR-16  VXR-16 DosimetryPro Wh

32 Installing device drivers VIDAR Film Digitizer Installation Guide About the STI drivers Previously, most system integrators built their scanning a

Installing device drivers 33 VIDAR Film Digitizer Installation Guide WARNING: VIDAR has validated the STI driver and replacement of vscsi32.dll wi

34 Installing device drivers VIDAR Film Digitizer Installation Guide Computers with Windows NT 4.0 (Service Pack 5 or higher) You will need:  Adapt

Installing device drivers 35 VIDAR Film Digitizer Installation Guide 4. In the SCSI Adapters window, click the Drivers tab (see below). 5. In the

36 Installing device drivers VIDAR Film Digitizer Installation Guide 6. In the Install Driver window (shown below): a. In the left list, select Adap

Installing device drivers 37 VIDAR Film Digitizer Installation Guide 8. Insert the Adaptec™ SCSI Card 2930 Installation CD into the CD drive. 9.

38 Installing device drivers VIDAR Film Digitizer Installation Guide 12. In the Files Needed window, confirm the path, then click OK. 13. In the S

Installing device drivers 39 VIDAR Film Digitizer Installation Guide 15. In the SCSI Adapters window: a. Verify that the Adaptec SCSI adapter is

40 Installing device drivers VIDAR Film Digitizer Installation Guide 18. Remove the VIDAR Drivers and Toolkit Installation CD. IMPORTANT: Please s

Installing device drivers 41 VIDAR Film Digitizer Installation Guide Computers with Windows 98 Second Edition You will need:  Adaptec™ SCSI Card

End user information End user administrative contact Name Title Company name Telephone no. E-mail address Fax no. End user technical contact Name

42 Installing device drivers VIDAR Film Digitizer Installation Guide 11. Remove the VIDAR Drivers and Toolkit Installation CD. IMPORTANT: Please sa

43 VIDAR Film Digitizer Installation Guide Operating About digitizers and film sizes This manual covers several digitizer models. This section d

44 Operating VIDAR Film Digitizer Installation Guide VXR-16 DosimetryPRO™ specifications Nominal resolution Pixels (14"x17" film) Spot size

Operating 45 VIDAR Film Digitizer Installation Guide About films The film digitizer handles standard radiograph films up to 14" x 17" (35

46 Operating VIDAR Film Digitizer Installation Guide Basic operating instructions 1. Turn on the film digitizer. Note: Always turn on the film dig

Operating 47 VIDAR Film Digitizer Installation Guide Scanning a single film Options for scanning single films There are two ways to scan a single f

48 Operating VIDAR Film Digitizer Installation Guide Note: When a film has been staged, it is in the digitizer’s light path. The ADC (Automatic Digi

Operating 49 VIDAR Film Digitizer Installation Guide Scanning multiple films CAUTION: Do not load more than 25 films at one time. 1. Hold the f

50 Operating VIDAR Film Digitizer Installation Guide Note: When a film has been staged, it is in the digitizer’s light path. The ADC (Automatic Digi

Operating 51 VIDAR Film Digitizer Installation Guide Cleaning the Auto-Feed Roller After extensive use, dust or lint particles may build up on the

52 VIDAR Film Digitizer Installation Guide Appendix: SCSI information and troubleshooting guide Introduction VIDAR digitizer installation instru

Appendix: SCSI information and troubleshooting guide 53 VIDAR Film Digitizer Installation Guide Digitizer and SCSI controller compatibility VIDAR

54 Appendix: SCSI information and troubleshooting guide VIDAR Film Digitizer Installation Guide Connecting the cable Note: Attach or remove the SCS

Appendix: SCSI information and troubleshooting guide 55 VIDAR Film Digitizer Installation Guide Troubleshooting Tip: Check www.filmdigitizer.com

56 Appendix: SCSI information and troubleshooting guide VIDAR Film Digitizer Installation Guide  Problem: System locks up or freezes when the driv

Appendix: SCSI information and troubleshooting guide 57 VIDAR Film Digitizer Installation Guide  Problem: SCSI card driver not loading or hangin

460 Springpark Place Herndon, VA USA 20170 Phone: 1-703-471-7070 Fax: 1-703-471-1165 Technical Support: 1-703-471-7070 1-800-471-72

Documentation questionnaire for VIDAR film digitizers Instructions: 1. Cut along dotted line at left. 2. Fill in. 3. E-mail or fax to VIDAR. 460 Sp

How could this document be improved? Other comments or suggestions on how VIDAR Systems can improve its documentation and products:

Installation guide for DiagnosticPRO™ DiagnosticPRO plus™ VXR-16 DosimetryPRO™ VXR-16™