Adaptec GDTSETUP Manual do Utilizador descarregar pdf (Página 54)

*'75'+:/0%5$0N%N%)ODVK5$0

*'75'+:/

stands for the type of ICP Controller found by the GDT BIOS. HWL

means Hardw

are level.

0%5$0

indicates that the installed SIMM is a 16MB, non-parity

Fast Page Mode (FPM) SIMM. Depending on the type and size of the installed SIMM the

following messages are possible (xx = 4, 8, 16, 32, 64, 128):

[[0%5$0

xx MB Fast Page Mode (FPM) SIMM without parity (i.e. 32 bit)

[[0%5$03

xx MB Fast Page Mode (FPM) SIMM with parity (i.e. 36 bit)

[[0%('25$0

xx MB Extended Data Out (EDO) SIMM without parity (i.e. 32 bit)

[[0%('25$03

xx MB Extended Data Out (EDO) SIMM with parity (i.e. 36 bit)

When a parity SIMM is installed this message is followed by:

(&&3DULW\VXSSRUWHQDEOHG

N%N%)ODVK5$0

indicates the size of the installed Flash-RAM. "1024kB" refers to the

onboard Flash-RAM size. The "/0kB" stands for an empty Flash-RAM expansion socket (Fea-

ture Socket).

6&6,$

indicates the SCSI devices connected with the controller's Wide/Ultra2 SCSI channel.

The last SCSI channel (in our example SCSI-B indicates the SCSI device connected with the

controller's Narrow/Ultra SCSI channel. With a GDT6558RD this would be SCSI-F).

3UHVV&75/!*!WRHQWHU*'76(783!!!

After pressing this hot-key, the message

(QWHULQJ*'76(7833OHDVHZDLW

appears. The SCSI

bus scan is completed and the built-in GDTSETUP configuration program is loaded. It al-

lows you to configure RAID Array Drives.

%7URXEOH6KRRWLQJ

If these messages do not appear on the screen, or if other problems occur after switching

on the computer system (screen remains dark etc.), you should check the entire installation

over again:

 Are you using the correct SIM-module ? (Minimum 8MB, 60ns or faster for FPM and

50ns for EDO) Try another one.

 SIMM plugged firmly into the socket ? Unplug it and plug it in again.

 Is the ICP Controller plugged into a PCI bus-master Slot ? Check this. If necessary, try an-

other slot.

 Is the SCSI cable OK ? Check the length and connectors, Try another cable..

If the

PCI System-BIOS is not PCI 2.x compatible

(see above), the ICP Controller BIOS

may display one or more of the following messages:

(i) The DPMEM has not been installed correctly.

(UURU 6\VWHP%,26QRW3&,FRPSOLDQWFRQWDFW\RXUPDLQERDUGVXSSOLHU

&RQWUROOHUDW[\KDVLQYDOLG'30(0DGGUHVV

7U\LQJWRDOORFDWHDIUHHDGGUHVV

)RXQGIUHHDGGUHVVDWDFFHSW"<HV1R$ERUW<

&DXWLRQWKLVDGGUHVVPXVWQRWEHXVHGE\DQRWKHUH[SDQVLRQFDUG

In this case, the system-BIOS has not installed the Dual Ported Memory of the ICP Con-

troller correctly. Therefore, the ICP Controller will search for an adequate address. If you

accept the suggested address (

), the ICP Controller will install its DPMEM starting at this

address. Since this 16KB address space which starts at

IUHHDGGUHVV

must not be shadowed,

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 217 218

Comentários a estes Manuais

Sem comentários

Adaptec GDTSETUP Manual do Utilizador Página 54

Comentários a estes Manuais

Manuais e produtos relacionados com Software Adaptec GDTSETUP